EMotimo TB3 Black User Manual

1 | P a g e miniDF Manual v.1.1 miniDF manual. V1.1 2015-02-22 © A1net 2015, all rights reserved. NEVER CONNECT A MOTOR WHILE THE DRIVER I

10 | P a g e miniDF Manual v.1.1 Micro stepping stepping Chart 1 2 3 Microstep Low Low Low Full step High Low Low Half st

11 | P a g e miniDF Manual v.1.1 4.0 Lens Motors. NEVER CONNECT A MOTOR WHILE THE DRIVER IS POWERED. NEVER DISCONENCT A MOTOR WHILE THE

12 | P a g e miniDF Manual v.1.1 MOD.8 in metric units. Follow focus devices and focus motors have teeth of this size to mesh with the gear

13 | P a g e miniDF Manual v.1.1 The Lensmotor focus motor has a clamp with a 15mm hole that can be tightened around one of the 15mm rod

14 | P a g e miniDF Manual v.1.1 reach so the gears can reach each other and mesh. Changing the number of teeth on the output gear has the

15 | P a g e miniDF Manual v.1.1 Appendix A: miniDF v3 schematic and board. Schematic of the miniDF Minidf v.3 board layout

16 | P a g e miniDF Manual v.1.1 Appendix B: Arduino nano v3 and Arduino software. In order to get more information about the arduino nano

17 | P a g e miniDF Manual v.1.1 Appendix C: Installing DFmoco and DFremote. The miniDF cames preinstalled with the DFmoco script revision

18 | P a g e miniDF Manual v.1.1 Appendix D: Dragonframe serial interface. Information from: http://www.dragonframe.com/arduino/serial.php

19 | P a g e miniDF Manual v.1.1 Appendix E: DFRemote. The dfRemote script can be loaded into the miniDF. Below is the example of the dfRemo

2 | P a g e miniDF Manual v.1.1 1.0 The Stepout miniDF system. The Stepout miniDF is a motion control system for Dragonframe stop motion

20 | P a g e miniDF Manual v.1.1 * DF_LIVE_CMD - goes to live (also re-engages live view) */ /* * Configure output pins. T

21 | P a g e miniDF Manual v.1.1 Appendix F: Dragonframe Arduino serial protocol. Serial Port Settings Baud Rate 56000 kbps Data Bits 8

22 | P a g e miniDF Manual v.1.1 Appendix G: StepSlice schematic and board. StepSlice awa09 schematic StepSlice awa09 board

3 | P a g e miniDF Manual v.1.1 2.0 The miniDF. The miniDF device is based on the Arduino nano v3.0 and designed to interface with Dragonf

4 | P a g e miniDF Manual v.1.1 Front of unit: 1) Push button: kill switch. It has to be activated by editing the DFmoco script 2) Micro U

5 | P a g e miniDF Manual v.1.1 If the user wishes to use an external trigger for the kill switch it can connect a pushbutton or a limit

6 | P a g e miniDF Manual v.1.1 motor driver. Each miniDF can run four simultaneous stepper motor drivers to control four independent motori

7 | P a g e miniDF Manual v.1.1 3.0 StepSlice. StepSlice Silver edition NEVER CONNECT A MOTOR WHILE THE DRIVER IS POWERED. NEVER DISC

8 | P a g e miniDF Manual v.1.1 Connect the motor to the stepper driver while the driver is not powered. After that, power the driver. Disco

9 | P a g e miniDF Manual v.1.1 There are two different versions of the StepSlice: Silver and Black. StpepSlice Black Edition The silver e